Pololu Dual VNH5019 Bedienungsanleitung

Pololu Dual VNH5019 Motor DriverShield User’s Guide1. Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Power Connections and ConsiderationsDual VNH5019 motor driver shield power buses when connectedto an Arduino.In the shield’s default state, the motor

Dual VNH5019 motor driver shield with an Arduino (Arduino powered by the shield).It is also possible to power your Arduino directly from the motor shi

Each VNH5019 motor driver IC has a maximum continuous current rating of 30 A. However, the chips by themselveswill overheat at lower currents. In our

Motor with one 0.1 uF capacitorsoldered across its terminals.Motor with two 0.1 uF capacitorssoldered from its terminals to itscase.1. Solder a 0.1 µF

delay(2);}for (int i = 400; i >= -400; i--){md.setM1Speed(i);stopIfFault();if (i%200 == 100){Serial.print("M1 current: ");Serial.println(

4. Using as a General-Purpose Motor DriverThe set of pins along the left side of the shield provides direct access to the VNH5019 motor drivers, which

4.b. Board ConnectionsDual VNH5019 motor driver shield connected to a microcontroller (gray connections areoptional).The above diagram shows the minim

PIN Default State DescriptionVINThe connection point for the positive side of the 5.5 – 24 V motor power supply.Since the overvoltage protection can b

Power ConsiderationsDual VNH5019 motor driver shield power buses when not used withan Arduino shield.The shield must be supplied with 5.5 to 24 V thro

5. Schematic DiagramPololu Dual VNH5019 Motor Driver Shield User’s Guide © 2001–2014 Pololu Corporation5. Schematic Diagram Page 19 of 28

Pololu dual VNH5019 motor driver shieldfor Arduino.Pololu dual VNH5019 motordriver shield, assembled andconnected to an Arduino Uno R3.1. OverviewThis

Pololu Dual VNH5019 Motor Driver Shield User’s Guide © 2001–2014 Pololu Corporation5. Schematic Diagram Page 20 of 28

Schematic diagram of the Pololu dual VNH5019 motor driver shield for Arduino.This schematic is also available as a downloadable pdf: dual VNH5019 moto

6. Customizing the ShieldThis motor driver shield has several features that will not be useful in a typical application but that might benefit anadvan

In all cases, the top through-hole of the pair connects to the Arduino pin and the bottom through-hole connects to themotor driver pin. To change one

only ENA/DIAGA will have the required pull-up resistor; you will need to add a separate pull-up resistor for theENB/DIAGB pin, or connect it to a micr

7. Using the Driver in Single-Channel ModeThe dual VNH5019 motor driver shield uses two VNH5019 motor driver ICs to enable independent control of twob

Arduino pin remapping of dualVNH5019 motor driver shield forsingle-channel mode (view ofunderside of PCB).PWM INA INB OUTA OUTB operating mode0 0 0 OP

#include "DualVNH5019MotorShield.h"// configure library with pins as remapped for single-channel operation// this lets the single motor be c

8. Differences between board revisionsThere have been two versions of the dual VNH5019 motor driver shield. The revision identifier, ash02a or ash02b,

Pololu dual VNH5019 motordriver shield for Arduino, bottomview with board dimensions.• Wide operating voltage range: 5.5 – 24 V1• High output current:

Pololu dual VNH5019 motor driver shield forArduino with included hardware.1.b. Included HardwareThis motor driver board ships with all of the surface-

Pololu dual VNH5019 motordriver shield, assembled andconnected to an Arduino Uno R3.2. Contacting PololuWe would be delighted to hear from you about a

3. Getting Started with an ArduinoAs with virtually all other Arduino shields, connections between the Arduino and the motor driver are made viaextend

3.b. Assembly for Use as an Arduino Shield1. Stackable Arduino headers: Before you can use this board as an Arduino shield, you need to solder fourof

thick wires with high-current connectors [http://www.pololu.com/product/925] should be soldered directly to theboard. The smaller holes are intended o

Default Arduino Pin MappingsThe following table shows how the shield connects your Arduino’s pins to the motor drivers’ pins:Arduino Pin VNH5019 Drive